10 free sample questions from a bank of 57, with the correct answers and explanations. No signup required — start practising right now.
1Which is a family of solutions for data center designs that span compute, storage, networking, and management, serving as a blueprint for a customer's Software
Defined Data Center (SDDC) implementations? (Choose the best answer.)
VMware SDDC Design
VMware Validated Design
VMware POC Design
VMware Cloud Foundation
Answer: B
2Which two benefits can be achieved using in-band management of an NSX Bare Metal Edge Node? (Choose two.)
Reduces storage requirements.
Reduces cost.
Preserves packet locality.
Reduces egress data.
Preserves switchports.
Answer:
3An architect is helping an organization with the Physical Design of an NSX-T Data Center solution.
This information was gathered during a workshop:
✑ Any proposed solution must provide low latency.
✑ Any proposed solution must provide high throughput.
✑ Customer is running stock trading applications.
Which two selections should the architect recommend to meet high-performance workload requirements? (Choose two.)
Leverage ESXi as the compute host.
Use LACP for all uplink profiles.
Leverage KVM as the compute host.
Enable enhanced data path mode on the N-VDS.
Enable latency sensitivity mode on the N-VDS.
Answer:
4Which selection is associated with the Review Task of the Engagement Lifecycle? (Choose the best answer.)
Gather and document requirements, assumptions, and constraints.
Build, deploy, implement, and test the design.
Measure performance against customer's objective.
Create and document the logical and physical design.
Answer: C
5An architect is helping an organization with the Logical Design of an NSX-T Data Center solution.
This information was gathered during the Assessment Phase:
✑ NSX-T will span across two sites for disaster recovery.
✑ Public Load Balancer VIP should be accessible from a secondary site.
✑ Distributed Firewall Policies should be available at a secondary site.
✑ Routing capabilities should be maintained after failure.
✑ NAT capabilities are required.
Which two selections should the architect include in their design? (Choose two.)
Use of the same ISPs across sites.
Use two separate ISPs across sites.
Use MTU to 1550 between sites.
Set MTU to 1550 between sites.
Use IP sets or groups to configure DFW rules.
Answer:
6An architect is helping an organization with the Conceptual Design of an NSX-T Data Center solution.
Which risk is documented by an architect? (Choose the best answer.)
The security team has a firewall communication matrix documented.
The team is not trained for NSX-T but have a very strong experience with vSphere.
Open communication between different application tiers is not allowed.
Aggregate N-S throughput at any given time should be at least 10G.
Answer: B
7An architect is helping an organization with the Logical Design of an NSX-T Data Center solution.
This information was gathered during the Assessment Phase:
✑ Data between two networks connected over a public network needs to be encrypted.
✑ Certificate authentication is required.
✑ Dynamic route learning is preferred.
Which selection should the architect include in their design? (Choose the best answer.)
Deploy a Tier-0 gateway in Active/Standby mode. Configure policy-based IPSec VPN with SHA512 with RSA as the hash algorithm.
Deploy a Tier-0 gateway in Active/Active mode. Configure route-based IPSec VPN with SHA512 with RSA as the hash algorithm.
Deploy a Tier-0 gateway in Active/Standby mode. Configure route-based IPSec VPN with SHA512 with RSA as the hash algorithm.
Deploy a Tier-0 gateway in Active/Active mode. Configure policy-based IPSec VPN with SHA512 with RSA as the hash algorithm.
Answer: C
8An architect is helping an organization with the Physical Design of an NSX-T Data Center solution.
This information was gathered during a workshop:
✑ Migrating existing data center to KVM hosts.
✑ Redundancy and high availability are required.
✑ No component can be a single point of failure.
Which selection should the architect recommend? (Choose the best answer.)
Linux Bridge redundancy with Active/Active Mode and multiple pNICs with necessary binding
Linux Bridge redundancy with Active/Active Mode and single pNIC with static binding
vSS/vDS in Active/Standby Mode with necessary binding
vSS/vDS in Active/Active Mode with necessary pNICS and required binding modes
Answer: C
9An architect is helping an organization with the Conceptual Design of an NSX-T Data Center solution.
This information was gathered by the architect during the Discover Task of the Engagement Lifecycle:
✑ There are applications which use IPv6 addressing.
✑ Network administrators are not familiar with NSX-T Data Center solutions.
✑ Hosts can only be configured with two physical NICs.
✑ There is an existing management cluster to deploy the NSX-T components.
✑ Dynamic routing should be configured between the physical and virtual network.
✑ There is a storage array available to deploy NSX-T components.
Which risk was documented by the architect? (Choose the best answer.)
Network administrators are not familiar with NSX-T Data Center solutions.
Dynamic routing should be configured between the physical and virtual network.
There are applications which use IPv6 addressing.
There is a storage array available to deploy NSX-T components.
Answer: A
10An architect is helping an organization with the Physical Design of an NSX-T Data Center solution.
This information was gathered during a workshop about ESXi Host networking:
✑ A total of 50 ESXi hosts to be configured as Transport Nodes.
✑ All ESXi hosts have a dedicated 2 × Intel 10Gbps Physical Network adapter for the Overlay Traffic.
To achieve low latency, high throughput, redundancy, and performance, which two NIC teaming policies should the architect recommend? (Choose two.)